The Blastcrete Model RD6536 skid-steer concrete pump is designed to pump up to ¾-inch aggregate concrete using a skid steer with 15 gpm auxiliary hydraulics up to 25 cubic yards per hour. The RD6536 can pump in both forward and reverse, and can pump various types of viscous material including sludge, sewage and draining pounds. Other uses include shotcrete, floor overlayment, masonry grout and ICF.
World of Concrete Booth SG2
Circle 161 on Reply Card • freeproductinfo.net/rer
Arrow-Master introduces the F-Series direct-drive, walk-behind power trowels. The direct-drive gear case and lower center of gravity provide reliable power with less wobble and side torque for a smoother finish. The walk-behind power trowel also features a fully enclosed spider assembly that protects the blade arm and pitch-control components, and allows for easier cleanup. The F-Series is available in 30-, 36- and 46-inch diameters, as well as a wide range of engines and horsepower ratings.
Circle 162 on Reply Card • freeproductinfo.net/rer
General Equipment's SP8/G Series II surface planer is designed for a range of applications including milling misaligned sidewalks and joints, removing thermo and cold plastic markings and prepping floors for new coating applications. The unit has a maximum cutting depth of 5/8 inches, a cutting width of 8 inches and a cutting proximity to a vertical wall of 3¼ inches. Cutting depth is adjusted using a screw-type, positive-locking depth selector, and the wheels located behind the drum make it easier to cut through high spots.
World of Concrete Booth S11013
Circle 163 on Reply Card • freeproductinfo.net/rer
The Model 65B on-grade concrete drill from E-Z Drill operates on a minimum of 20 cfm. The machine drills holes from ½- to 7/8-inch in diameter and can be adjusted to center on slabs as thick as 2 feet. It can drill to 8 inches deep in a 2-foot patch and to a depth of 12 inches in a 30-inch area. The E-Z Drill 65B weighs 65 pounds, allowing it to be loaded, unloaded and repositioned by a single operator. An optional vertical conversion kit increases the unit's versatility, allowing it to switch from horizontal to vertical drilling after a 20-minute installation.
World of Concrete Booth S11427
Circle 164 on Reply Card • freeproductinfo.net/rer
The 4-blade B Series (pictured) and J Series walk-behind power trowels from MQ/Whiteman feature more powerful engines to generate improved rotor speeds of between 60 to 155 rpm for smoother finishes. The four B Series models, with 46-inch ring diameters, and six J Series models, with 36-inch diameters, also feature an ergonomic throttle control, lifting bail, and rugged spider assembly for extended life. The trowels also include a height-adjustable 2-inch diameter tubular-steel handle for improved operation comfort and workability.
World of Concrete Booth C4813
Circle 165 on Reply Card • freeproductinfo.net/rer
Atlas Copco Construction Tools
Atlas Copco Construction Tools introduces the SB 552 hydraulic breaker attachment. The breaker is designed for a range of applications including demolition, road construction, building renovation, foundation work, trenching, landscaping and secondary breaking. The 1,149-pound SB 552 weighs 210 pounds more than the previous model, the SB 450. The breaker offers a high power-to-weight ratio and is suitable for carriers in the 9- to 15-metric ton weight class. The SB 552 delivers a maximum impact rate of 1,080 blows per minute and requires oil flow of 17.2 to 30.4 gpm at a pressure range of 1,450 to 2,180 psi.
World of Concrete Booth C4557
Circle 166 on Reply Card • freeproductinfo.net/rer
Wacker's CRT 36 ride-on trowel series offers a choice of two engine options (Wacker or Honda) and a patent-pending integrated wheel kit. The new center-engine design offers improved visibility, and the compact, heavy-duty frame provides a solid feel for the operator and allows easy access to the slab edges. The CRT 36 series features blade speeds from 20 to 165 rpm and a variable clutch, which provides proper torque and speed range to match concrete conditions without mechanical adjustments. A front and rear lighting system provides accuracy and better visibility on dimly lit jobsites.
World of Concrete Booths C4129 and C4215
Circle 167 on Reply Card • freeproductinfo.net/rer
The KHA24 from Metabo is a 24-volt lithium-ion-powered rotary hammer and can drill precise, straight holes in concrete, block, brick or stone using SDS-Plus carbide-tipped drill bits. The KHA24's Vibratech anti-vibration side handle and the vibration-dampening rear handle protect the user when chipping, rotary hammering and rotary drilling. With a no-load speed of 1.040 rpm, the rotary hammer offers a capacity of ¾ inches in concrete using solid bits.
World of Concrete Booth S13431
Circle 169 on Reply Card • freeproductinfo.net/rer
The MBW MK8-75H ride-on trowel features twin 30-inch rotors, an edger system for finishing nearly flush to walls, and can be equipped with finish or combo blades and float pans. The lightweight unit can maneuver in tight quarters including passing through a 32-inch doorway. The 433-pound unit also features three rollers on its front guard ring, enabling it to finish within approximately ¼-inch of a wall. The MK8-75H can be transported in the bed of a typical pick-up truck.
World of Concrete Booth C4355
Circle 168 on Reply Card • freeproductinfo.net/rer
The vibration-reduced CP 0017 SVR chipping hammer from Chicago Pneumatic Construction Tools features upgraded features for improved wear resistance. Two versions of the hammer are available, both equipped with a screw cap tool retainer and small shanks to keep the units lightweight. The SP 0017 SVR 3R (pictured) weighs 20.5 pounds and has a 0.68-inch round shank, while the CP 0017 SVR 3H features a 0.58-inch hex shank and weighs 21 pounds. The unit also features a standard D-type ergonomic trigger handle.
World of Concrete Booth S11709
Circle 170 on Reply Card • freeproductinfo.net/rer
The WS-Series of concrete saws from Ingersoll Rand offer cutting depths from 4.6 to 15 inches with 12- to 36-inch blades. The nine models of walk-behind concrete saws come with Honda, Wisconsin or Deutz engines, which are solidly mounted to the saw's frame to prolong engine life. They are designed for construction and expansion joints, utility installations, asphalt and concrete patch repairs, short-run slab cutting, trenching and traffic loop installation.
World of Concrete Booth O31057
Circle 171 on Reply Card • freeproductinfo.net/rer
The Edco DS-18 concrete and asphalt saw comes equipped with either a 13-hp gasoline engine or a 5-hp electric motor. The saw also features a heavy-duty, anti-vibration engine mount; a 7-gauge, solid-steel frame; and 18-inch blade capacity with dual-arbor cutting along with lifting handles. The DS-18 offers perfect balance, which is key to performance, long blade life, smooth cuts and eliminates excessive wear and tear, according to the manufacturer.
World of Concrete Booths S10139, O30722 and O30728
Circle 172 on Reply Card • freeproductinfo.net/rer
The Mini diamond drill, END 712 P, from CS Unitec is designed for drilling dowel, anchor and thru holes in tile, natural stone and concrete. The drill offers variable speeds up to 8,000 rpm for easy starting and fast drilling; drills without shock or hammering; and eliminates cracks or blow-outs. The lightweight 5-pound diamond drill comes equipped with a keyless chuck, carrying case and depth gauge.
World of Concrete Booth S10949
Circle 173 on Reply Card • freeproductinfo.net/rer
Stone Construction Equipment
Stone Construction Equipment offers 12 Champion concrete mixers available in 2-, 4-, 6-, 7-, 9-, 10- and 12-cubic-foot mixing capabilities. These units come in standard side- and end-dump versions and are equipped with a choice of engine options including Briggs & Stratton, Honda and Robin. The 9-cubic-foot mixer features a polyethylene drum option.
World of Concrete Booth N2603
Circle 174 on Reply Card • freeproductinfo.net/rer
Bobcat introduces the HB280 (pictured) and HB2380 hydraulic breaker attachments. Available for use only with the Bobcat 316 compact excavator, the HB280 is in the 60-foot-pounds impact energy class and has a CIMA rating of 59 foot pounds. The HB2380 is approved for use on Bobcat large-frame loaders and the 442 ZTS compact excavator. The HB280 weighs 127 pounds and provides 1,120 to 1,290 blows per minute through a hydraulic flow of 3.4 to 6.1 gpm. With a hydraulic flow range of 19.8 to 33 gpm, the HB2380 provides 600 to 950 blows per minute and has a CIMA rating of 700 foot pounds.
World of Concrete Booth C5483
Circle 175 on Reply Card • freeproductinfo.net/rer